GSP-818 is a new general spectrum analyzer, which supports a frequency range of 1.8 GHz and provides testing requirements for RF products during the development/production phases. GSP-818 has a built-in 20dB amplifier and provides an adjustable range of resolution bandwidth (RBW) from 10Hz to 3MHz. In addition, it has the AM/FM signal demodulation function and the ACPR/OCBW/CHPW test functions to meet the requirements of general RF signal measurement.
GSP-818 Spectrum Analyzer
$2,000
- Frequency Range: 9kHz ~ 1.8GHz
- RBW: 10Hz ~ 3MHz, 10Hz ~ 500kHz in 1-10 steps
- Sensitivity: -148dBm/Hz Typical @PreAmp On
- Built-in AM/FM Demodulation
- Bandwidth Zoom function
- Measurement Function: ACPR/OCBW/CHPW, NdB Bandwidth, Freq. Counter, Noise Marker, Limit Line
- Built-in 20dB Preamplifier Standard
- Interface: Lan, USB
- Screen: 10.4″ SVGA Output (800*600)
- Options: Tracking Generator, EMI Filter & Detector (via software keycode)
$2,000
500VA AC Test Capacity
Short Current > 200mA
240×64 Ice Blue Dot matrix LCD
Sweep Function for DUT characteristic analysis
Insulation resistance measurement up to 50GΩ(GPT-9903A/9904)
Manual/Auto Mode
Function Key for quick selection
High intensity flash for caution & Status indication
Safety INTERLOCK function
Zero Crossing Turn-on Operation
Controllable Ramp-up Time
$1,000
- Wide Test Frequency：
- — LCR-8200A:DC, 10Hz~50/30/20/10/5 MHz
- — LCR-8200:DC, 10Hz~30/20/10/5/1 MHz
- 7″ LCD color Display
- 0.08% Basic Accuracy
- Displaying Four Measurement Results Simultaneously From 17 Selectable Measurement Parameters Freely
- 15 Steps List Measurement
- Two Curves Sweep Mode
- Equivalent Circuit Model Analysis (LCR-8200A only)
- Internal DC Bias Voltage ±12V
- USB Storage Available
$2,000
- 5” TFT LCD
- Voltage/Current Test Freq. Bandwidth: DC, 0.1Hz~ 100kHz
- Waveform Display : V (Voltage), I (Current), P (Wattage)
- Distorted wave Current/Voltage measurement: full range for CF=3, and half range for CF=6 (or 6A)
- Meeting IEC 61000-4-7 harmonic measurement (50/60Hz)
- Wiring selecting button (1P3W,3P3W,3P4W,3V3A)
- Harmonic measurement & analysis up to 50 orders
- Auto ranging function for Integration mode
- Screen Capture through USB host
- Provide external current sensor input (EXT1/EXT2)
- Standard Interface: RS-232C, USB device/ host, LAN；Optional Interface: GPM-DA12 – GPIB + Digital I/O (factory installed only)
$2,000
- 200/100/70MHz bandwidth selections, 2ch input
- 100/70/50MHz bandwidth selections, 4ch input
- 1GSa/s maximum sampling rate
- 10M maximum memory depth for each channel
- 7” 800 x 480 WVGA LCD display
- 256 color gradient display function to strengthen waveform performance
- I2C/SPI/UART/CAN/LIN serial bus trigger and decoding functions
- 1Mpts FFT frequency domain signal display
- Zero Key function for horizontal time, vertical voltage and triggering
- Compact and innovative exterior design
$2,000
- 1uHz to 20 or 30MHz, 16-bit resolution with 1 mVpp to 10 Vpp amplitude. 1 or 2 channel (s)
- 250 MSa/s sampling rate for higher time resolution arbitrary waveforms
- 8M Points/channel standard waveform memory
- Input/output signal ground independent of housing and signal ground between channels also insulated.
- Synchronized phase operates up to 6 units and 12 channels
- Pulse waveform parameters can be set independently for more precise timing
- Harmonic signal generator
- Dual channel models support SUM modulation, coupling, tracking, and phase functions
- Built-in AM/FM/PM/FSK/PWM/SUM modulation, sweep and burst functions
- Provide USB/LAN/GPIB (optional) instrument control interface
- IQ baseband waveform output function for AFG-3032/3022
Reviews
There are no reviews yet.